
Palo Alto, California · Electrician referrals
San Francisquito Electric is a referral line built for Palo Alto households. Calling costs nothing, being connected to an independent local electrician costs nothing, and money only enters the picture after you approve a written estimate.
San Francisquito Electric is a free referral service. We connect you with an independent local pro; we do not perform the work ourselves.
This line is operated from the United States. You reach a US based operator, not a call center overseas.
Electrician hooking up a generator in Palo Alto. Illustrative trade photo.
Palo Alto coverage follows the postal map: 94301 downtown and Old Palo Alto, 94302 for Barron Park post office routes, 94303 across the southern Eichler neighborhoods, 94304 on the Stanford side, 94306 through Midtown, and 94309 for the remaining box routes.
Expect two layers in any Palo Alto quote. The base layer is the published national frame: most small visits run about $150 to $800, and panel replacement commonly runs $1,500 to $4,000 and up as service size grows. The local layer is this city's own: panel and service work is scheduled with City of Palo Alto Utilities, the municipal provider, rather than a regional utility; homes near University Avenue can turn a standard swap into careful work around wiring from several earlier eras; and an Eichler panel replacement is an era project, sequenced through permits and inspection. Insurance answers sudden documented damage, such as a surge that killed equipment. It does not answer age, capacity, or a panel the decades outgrew. The proposal worth trusting is the one whose written scope shows the load math behind its total.
Nothing. The call and the referral are free, and there is no obligation to hire anyone.
Only after the pro has seen the job and you have approved a written estimate. Approving the price is always your decision.
An independent local contractor who takes this kind of work in Palo Alto. You deal with them directly, and you can verify licensing and insurance before hiring.
No. This service is run by a US based routing team. Real people here route your call to a local pro.
Panel swaps and service upgrades for houses whose original electrical heart has been outgrown: Eichler era panels, pre-war fuse boxes, and services that must now carry chargers, heat pumps, and full home offices.
Call PLACEHOLDER
Urgent help when a Palo Alto home loses power, smells of hot wiring, or shows sparks or scorching, with the city utility outage check built into the first minutes of triage.
Call PLACEHOLDER
Outlet, switch, dimmer, and ground fault work for homes full of two prong receptacles and modern three prong loads, with honest remedies for ungrounded circuits in older walls.
Call PLACEHOLDER
Circuit repairs and full or partial rewiring where early wiring types survive: knob and tube near the downtown core, cloth covered conductors, and the layered additions of a century of remodels.
Call PLACEHOLDER
Transfer switches, interlock kits, and inlets that let a portable or standby generator carry a house safely through a municipal outage, sized to the circuits that actually matter overnight.
Call PLACEHOLDER
A surge device mounted at the panel to blunt utility switching spikes and storm surges before they reach workstations, chargers, and the control boards inside modern appliances.
Call PLACEHOLDER
Fixture, recessed lighting, and ceiling fan work in rooms where the architecture argues back: Eichler glass and post and beam ceilings, and pre-war rooms with plaster worth protecting.
Call PLACEHOLDERDescribe what you are seeing. One free call connects you with an independent local pro who can assess it in person.
PLACEHOLDERPalo Alto pricing follows the wiring era of the house and the steps of a municipal utility, quoted in writing against published national bands.
See cost ranges and how insurance paysPublished national guides put electricians commonly at $50 to $100 or more per hour plus a service or trip fee, with small jobs (a device replaced, a fault traced) often landing between $150 and $400 all in. By the project: breaker panel replacement commonly runs $1,300 to $3,000, a generator interlock or transfer switch hookup $500 to $1,500, whole home surge protection a few hundred dollars installed, and whole home standby generators $10,000 to $15,000 or more installed. Written pricing after the assessment, with permit costs stated, is the number to compare.
A breaker trips for three reasons: the circuit is genuinely overloaded, there is a short or ground fault on it, or the breaker itself has failed. Resetting once after unplugging loads is reasonable diagnostics. A breaker that trips instantly, trips with nothing running, or feels warm is reporting a fault, and repeatedly forcing it is how a protection device becomes a fire starter. The tracing order is panel, then the circuit's devices and junctions, and the finding is usually a specific device, a damaged conductor, or an appliance confessing. That visit is a repair, not a mystery.
Whole house flicker under load (when the AC or a large appliance starts) points at the service: the connections at the meter, the mast, or the utility's own feed and neutral. A failing utility neutral is the serious version and it is the utility's repair, free to you, but it must be reported and it can damage electronics while it lasts. Flicker on one circuit is the home's side: a loose connection at a device or in the panel. An assessment that meters the service under load separates the two in one visit, and honest electricians check the utility side before quoting you a panel.
Sudden accidental damage is the covered kind: a lightning strike that kills the panel and appliances, storm damage to the service mast, a vehicle strike, fire damage. Wear, corrosion, obsolete equipment, and capacity upgrades for new loads are the owner's cost everywhere, even when they are wise spending. After a lightning event, document everything electrical that failed in the house on the same day; the pattern across devices is what ties a claim together. Panel upgrades sometimes matter to insurers in the other direction: replacing a known problem panel can be a condition of coverage on older homes, which your agent can confirm.
When the loads argue for it, yes; as a fashion, no. The honest triggers are concrete: no open breaker spaces with double tapped breakers making room, a generator, EV, hot tub, or addition planned, breakers warm or tripping under ordinary use, or a panel brand and era with a documented failure record. A 100 amp service running a small efficient home comfortably is not a problem to buy your way out of. The quote should state the load reasoning, the permit, and the grounding work included; a panel price without those is half a job.
Through an interlock kit or a transfer switch, full stop. Both connect the generator to chosen circuits through the panel and mechanically prevent power from ever flowing backward onto the street, where it can injure or kill a line worker restoring your neighborhood. Published guides put the hookup at $500 to $1,500 installed depending on method and distance. The two fatal shortcuts are the dryer outlet backfeed cord and running the generator in a garage; outage season produces carbon monoxide deaths every year from the second one alone. Generator outside, 20 feet from windows, feeding an inlet: that is the whole safe pattern.
Both are possible and the order of suspicion matters. A GFCI that trips with nothing plugged in and will not hold a test is often a tired device, and replacement settles it. A GFCI that trips when a specific appliance runs, or after rain at outdoor and dock locations, is reporting ground leakage from that appliance or water in a box, which is the device doing its exact job. At docks and pools, treat every trip as real until an assessment says otherwise, and keep people out of the water near a faulting circuit.
Not automatically, and anyone who says so without opening devices is skipping the assessment. Aluminum branch wiring from the late 1960s and 1970s fails at connections, not mid-run, and the approved remedies work at the connections: devices rated for aluminum, or copper pigtails with listed connectors installed by an electrician, at a fraction of whole house rewiring. The evidence that decides is at the devices: overheated, discolored, or loose aluminum connections argue for the full remedy program; clean, tight, properly rated connections argue for a monitored plan. Get the device level findings in writing either way.
The three causes, the safe tests, and the point where resetting stops being diagnostics and starts being risk.
Hourly rates, panels, generator hookups, and surge protection in published ranges, with permit reality included.
This service runs with US based staff. We connect you with independent local contractors and we stay accountable for that connection.
Prefer to talk later? Leave your details and an independent local pro will call you back. No charge to you, no obligation.
San Francisquito Electric is a free referral service. Submitting this form connects you with independent local contractors who provide the work.
Calls are answered 24/7. One call connects you with an independent local pro.
PLACEHOLDER