Free referral line for Palo Alto, CA: no charge to callers, no obligation until you approve a written estimate
PLACEHOLDER

Home · Services · Wiring & Rewiring

Wiring & Rewiring in Palo Alto, CA

Quick answer

Circuit repairs and full or partial rewiring where early wiring types survive: knob and tube near the downtown core, cloth covered conductors, and the layered additions of a century of remodels.

Rewiring in Palo Alto is partly preservation work. Professorville and Old Palo Alto walls can hold knob and tube installed when the house was new, and the plaster and millwork around it have their own value, so scopes here name the access plan room by room alongside the circuits. In Eichler tracts the puzzle inverts: wiring routed around post and beam framing and radiant era layouts. One city, two crafts, and a quote that confuses them has not walked either house.

Electrician testing continuity on a new run with a meter
Wiring & Rewiring. Illustrative trade photo.

Signs you need wiring & rewiring

What the job involves

1. The wiring is identified by type and era before scope: copper, aluminum branch, cloth, and knob and tube antiques each carry a different remedy and urgency.
2. Aluminum branch wiring is addressed with the approved remedies (rated devices and pigtailing systems or full replacement where argued), and the options are priced honestly against each other.
3. New circuits are run from panel capacity that actually exists; where it does not, the panel conversation happens first, in writing.
4. Work inside finished walls is planned for the fewest openings, and patching scope is named before anyone cuts.
5. Circuits are tested under load and labeled at the panel when the work closes.

What affects the price

When it is an emergency

Wiring work is planned work with three call now exceptions: heat or burning smell at a device, visible arcing, and any circuit that has started scorching. Aluminum wiring itself is not an emergency; it is a known remedy with a schedule, and anyone who tells you it must all come out this week without showing you device level evidence is selling, not assessing.

PLACEHOLDER

Wiring & Rewiring across the Palo Alto area

Related services

Wiring & Rewiring questions, answered

When is wiring & rewiring an emergency?

Wiring work is planned work with three call now exceptions: heat or burning smell at a device, visible arcing, and any circuit that has started scorching. Aluminum wiring itself is not an emergency; it is a known remedy with a schedule, and anyone who tells you it must all come out this week without showing you device level evidence is selling, not assessing.

What affects the price of wiring & rewiring in Palo Alto?

The main price factors for wiring & rewiring are covered in the cost section above. The contractor confirms the exact price in a written estimate after seeing the job, and nothing is owed until you approve it. The call and the referral are free.

Can knob and tube wiring stay if we insulate the attic?

That pairing is exactly where the trouble starts, and it is why the conversation belongs to an electrician before an insulation crew. Knob and tube was designed to dissipate heat into open air; burying it in insulation defeats the design, and many insurers and inspectors treat the combination as a finding. The scope options are a rewiring of the affected runs or an insulation plan that respects the wiring, and either belongs in writing before work starts.

How much does an electrician cost in Palo Alto?

Published national guides put electricians commonly at $50 to $100 or more per hour plus a service or trip fee, with small jobs (a device replaced, a fault traced) often landing between $150 and $400 all in. By the project: breaker panel replacement commonly runs $1,300 to $3,000, a generator interlock or transfer switch hookup $500 to $1,500, whole home surge protection a few hundred dollars installed, and whole home standby generators $10,000 to $15,000 or more installed. Written pricing after the assessment, with permit costs stated, is the number to compare.

My breaker keeps tripping. What does it mean, and can I just keep resetting it?

A breaker trips for three reasons: the circuit is genuinely overloaded, there is a short or ground fault on it, or the breaker itself has failed. Resetting once after unplugging loads is reasonable diagnostics. A breaker that trips instantly, trips with nothing running, or feels warm is reporting a fault, and repeatedly forcing it is how a protection device becomes a fire starter. The tracing order is panel, then the circuit's devices and junctions, and the finding is usually a specific device, a damaged conductor, or an appliance confessing. That visit is a repair, not a mystery.

Request a callback

Prefer to talk later? Leave your details and an independent local pro will call you back. No charge to you, no obligation.

San Francisquito Electric is a free referral service. Submitting this form connects you with independent local contractors who provide the work.

Call PLACEHOLDER Call now: PLACEHOLDER